Craftsman Table Saw Miter Slot Tab Removal
This article is from Issue 45 of Woodcraft Magazine.
With the saw unplugged, mark 1 blade tooth. Raise the blade almost all the way. With the marked tooth at the forward position, use a tri square, and measure the distance from tooth tip, to miter slot. Move the blade, to the rear position and measure again. This table saw does not have the traditional 3/4' x 3/8' miter slot and uses a very odd 5/8' wide T-slot. She will need to either file/sand the miter guage or get an adjustable one. Sears has a long history of making parts that only fit their equipment-after market parts and equipment do not fit. Here’s a link to a video that I made about my new crosscut / miter sled that I built for my Sears Craftsman 10” Table Saw with non-standard miter slots. I hope this helps some others who are looking for a solution to improve the accuracy of cross cuts and miter cuts with similar inadequately equipped table saws.
I have a Craftsman 113 series contractor table saw, which has an open back with the motor hanging out. I’ve been trying to figure out the best way to close this off so that the dust collector chute I have on the bottom of the saw would work better. All the solutions I’ve found online only seem to work with the blade at 90 degrees.
You only think your saw is working great.
Tuning up your tablesaw is one of the best steps you can take to becoming a better woodworker. You may think your saw is working just fine, but chances are it just isn’t performing as well as it could. Whether it’s an old saw or a new model fresh off the line, it probably has never been tuned up for premium performance. And tiny adjustments matter a lot when it comes to precision work.
Your saw’s table slots and fence may not be perfectly aligned to the blade path, causing rough or burned cuts. Blade angle stops that aren’t precisely dialed in can be causing less than perfectly square cuts. A misaligned splitter can lead to pinching or other feed problems, and stiff drive belts or poorly aligned pulleys could be causing vibration. These and other problems add up to a machine that’s not using its talents to its fullest.
Fortunately, it doesn’t take expensive tools or a lot of time to get your sawship shape. I’ll show you how to inspect, detect, and correct any shortcomings. I’m working on a cabinet saw in the photos, but most of the same principles apply to portable, contractor, and hybrid saws.
Tooling up
You probably already have most of the tune-up tools you’ll need, including a basic set of mechanic’s open-end wrenches, socket wrenches, Allen wrenches, and screwdrivers. You’ll also need a precision straightedge and an accurate square or two (Photo A). A 3' straightedge is perfect for our purposes here, but a 2' one (about $40) will work. A long, jointed piece of wood is okay for less precise measurements. A quality 4' engineers’ square will only set you back about $16, and art supply dealers sell plastic 45° drafting triangles for just a few bucks.
A feeler gauge (available at auto supply stores) is also useful (Photo B). Its thin metal leaves, gauged in thousandths of an inch, can be slipped into gaps to take precise measurements.
The only tool you may not have on hand is a dial indicator, and it’s well worth buying one for gauging the accuracy of many of your woodworking machines. (See sidebar on page 55.)
The tune-up sequence
There are certain tune-up steps that should be performed before others, depending on the type of saw you have and its condition. In general, approach the tune-up steps in the order presented here. I’ll note when deviations should be considered. Keep in mind that you may not need to make all of the following adjustments, as no fix may be required in some cases. However, make sure to check everything to determine where there might be problems.
Use a dial indicator to check the arbor flange for runout, which should be less than .001'.
Assess the arbor assembly
First check the integrity of the arbor assembly, which includes the arbor shaft, bearings, and pulley(s). Any slop in these parts can cause runout (wobble) in the arbor flange, which is a central tune-up reference point. If there’s a problem here (unlikely, except in well-worn older saws), there’s no point in continuing until it’s corrected because a wobbly flange will produce rough cuts even on an otherwise finely-tuned saw.
To check for slop, remove the drive belt(s) and try to move the arbor shaft up and down and in and out, listening and feeling for clunking noises or slop. Slowly spin the arbor, listening intently for grinding noises that might indicate worn bearings. Also try to spin and slide the pulley(s) while securely holding the arbor shaft. Any looseness here may indicate excessive wear that requires part replacement. The easiest fix for a faulty arbor assembly (again, unlikely), is to simply unbolt the entire arbor bracket (see your owner’s manual), and bring it to a machine shop for refurbishing.
Check the arbor flange for excessive runout, as any deviation here increases exponentially at the blade perimeter, causing rough cuts. Crank the blade carriage over to 45°, and scrub any crud from the flange with steel wool. Press the dial indicator plunger against the flange perimeter just enough to ensure contact throughout its rotation. Slowly rotate the arbor while monitoring the dial indicator (Photo C). The best saw manufacturers aim for less than .001' of runout. If you detect more, you’ll either have to live with it or replace the arbor.
Check the parallelism of the table slots to the blade using a dial indicator. Measure from the same spot on the blade, locating it both fore and aft.
Check blade and table slot alignment
For clean, accurate crosscuts, a workpiece must travel parallel to the blade. Since most crosscutting depends on a miter gauge or other jig that rides in the table slots, it’s important that the slots and blade are parallel. Any deviation results in blade heel that can cause rough, out-of-square cuts.
To best check the parallelism, screw a dial caliper to a scrap of wood that’s fastened to a snug-fitting runner in the table slot. I use a ZeroPlay guide bar, but a carefully fit wood strip will work, as long as there’s no sideways play. Fully raise your blade, and mark its plate near the perimeter. (The circular sticker in the photos is there only to provide better visibility.) Locate the mark near one end of the blade slot, lightly press the dial indicator against it, and zero-out the dial face (Photo D). Next, rotate the mark to the opposite end of the blade slot, and note the difference in measurement there to determine the amount of any non-parallelism (Photo E). (Rotating the blade like this eliminates any blade warp from the equation.)
No dial caliper? Use a feeler gauge to measure the distance between the blade and a screw in a stick of wood clamped to the miter gauge (left). If your miter gauge fits sloppily, attach the stick to a snug-fitting wood runner.
Lacking a dial caliper, you can go low-tech by driving a round-head screw into the end of a stick clamped to your miter gauge. Then use a feeler gauge to check the distance between the blade and screw, again measuring fore and aft of the blade slot (Photo F).
If your miter gauge bar fits sloppily, glue the stick to a snug-fitting wooden runner (Photo G).
If the parallelism is out more than .003', I recommend a realignment. (Note: With a cabinet saw, realignment is best done after cleaning the internal mechanisms, for which you’ll want to remove the saw top.) To align a contractor’s saw or portable saw, you’ll need to shift the position of the arc-shaped trunnion brackets, which bolt the entire saw carriage to the underside of the table. Loosen all four trunnion bolts, leaving one of the front bolts snug (but not tight) to serve as your pivot point. Next, use a soft-faced mallet to tap the rear trunnion bracket right or left as necessary to align the blade to the table slots.
On a cabinet saw, it’s easier. Simply loosen the four bolts that attach the saw table to the corners of the cabinet; then shift the table as necessary by tapping it at the edge with a mallet, as shown in the photo on page 52. Monitor your progress with a dial caliper.
When retightening the bolts, snug them up gradually in turn, as fully tightening one at a time risks shifting the trunnions or tabletop. Recheck the parallelism afterward.
Dial Indicators
For checking the accuracy of your tablesaw and other machines, it’s hard to beat a dial indicator. It consists of a spring-loaded plunger whose movement is indicated in thousandths of an inch on the face of a dial. You can use it to determine the concentricity of shafts, flanges, blades, and chucks, as well as the projection and travel of knives and other cutters.
To use the tool, secure it next to the part to be measured. A lug on the back allows attachment to an adjustable boom arm on a magnetic base (for convenience on ferrous metal surfaces.) Alternatively, you can screw through the lug hole into an appropriately sized piece of wood that’s clamped in place.
You don’t need an expensive dial indicator to measure most woodworking equipment. You can get a perfectly acceptable indicator and magnetic base for about $40.
Clean the internal mechanisms
For smooth operation, your saw’s pivot points, trunnion brackets, and gears need to be cleaned, lubricated, and kept free of oily sawdust that can gum up the works.
To familiarize yourself with the internals of your particular saw, refer to your machine manual. Don’t have it? Some manufacturers offer them online. Or simply scrutinize your saw. If you’re mechanically inclined at all, everything you need to see will be very apparent.
You can easily access the internals on a portable saw or contractors’ saw by turning it upside down on a bench. With a cabinet saw, the best approach is to remove the table. However, if the table is already well aligned to the saw blade, you may not want to remove it, especially if you have already built slot-traveling jigs that might then be thrown out of adjustment. Instead, work through the cabinet door, perhaps temporarily removing the motor for better access to the blade carriage and other parts.
Blast the interior with compressed air, and then use mineral spirits to clean away any crud and grease. Use a stiff-bristle toothbrush–continuously dipping it in the spirits–to clean gear teeth (Photo H) and other complicated parts. To expose the trunnion bracket grooves, fully crank the blade carriage over one way, and then the other (Photo I).
Lubricate the gears and trunnion grooves using a non-greasy, rust-protectant aerosol spray.
Lubricate all moving parts. Don’t use oil or grease on the gears or trunnions, as it attracts sawdust. Instead, spray them with a silicone-based lubricant (Photo J). Alternatively, you could apply a thin coat of paste wax, using a clean toothbrush for gear teeth and the like. To lubricate the arbor shaft, hand wheel shaft, and other pivoting points, use a thin penetrating oil like WD-40. Avoid getting lubricant on the belts or pulleys.
Eliminate vibration
A saw should stand solidly with no rocking, and be free of vibration in use. Rocking–usually caused by an uneven shop floor–can be corrected by shimming the saw feet. Working vibration is often caused by pulley misalignment, which can be corrected with the use of a straightedge held against the pulleys while adjusting them into the same plane. The stock die-cast pulleys on many contractors’ saws can also cause vibration due to non-concentricity. These can be replaced with machined steel pulleys.
“Belt slap”–caused by a rubber drive belt’s “memory” of its oblong packaged shape–can also cause working vibration. Replacing rubber belts with “link” belts eliminates this problem (Photo K). To tension a belt on a cabinet saw, pivot and lock the motor on its mount so that the belt deflects about 1' at its center point, as shown in Figure 1.
Vibration-free link belts can be sized to replace stiffened rubber V-belts that tend to gallop on their pulleys.
A jointed stick serves as a straightedge for aligning the saw table and extension wings.
Adjust the Allen screws in a stock throat plate to bring it level to the table.
Level the top
Check the level of the extension tables (or “wings”) using a long, jointed stick as a straightedge (Photo L). First flush up the wings to the main table. On a typical contractor’s saw, the extensions are bolted to both the saw table and the fence rails. If necessary, loosen the bolts, level the extension, and then retighten the bolts.
The cast-iron extensions on cabinet saws are typically bolted only to the main table. If an extension droops at its outer end, raise it by inserting paper, plastic, or aluminum shims at the underside of the joint. If the outer edge of the wing is too high, insert the shims at the topside of the joint. Finally, adjust the height of your throat plate using its leveling screws, with a short straightedge spanning the plate opening (Photo M).
Adjust the blade stops
Stops for setting the blade at 90° and 45° typically consist of an internal adjustable bolt that is locked in position with a jam nut (Photo N). Refer to your saw manual for the location of the stops, or just peer inside the saw while cranking the carriage over.
Craftsman Table Saw Miter Slot Tab Removal Kit
Check the blade at 90° and 45° in turn, with the blade carriage cranked completely against each stop without excessive pressure. A plastic 45° drafting triangle is perfect for the job (Photo O). Adjust each stop as necessary.
Follow up by taking a few test crosscuts and miter cuts on thick, narrow sticks of straight, dressed stock, trimming off at least 1⁄4' to prevent blade deflection. (Lacking an accurate miter square, you can place two mitered test cuts together against a good try square to check for a tight joint at 90°.) If the test cuts don’t prove accurate, readjust the stops. When they’re set correctly, tighten the jam nut on each, and repeat the test cut procedure.
Craftsman Table Saw Miter Slot Tab Removal Tool
Align the splitter
A properly aligned splitter or riving knife is crucial for preventing kickback, which is the primary cause of tablesaw accidents. Place an accurate straightedge against the right-hand face of the teeth (not the blade plate); then align the splitter or riving knife to the straightedge (Photo P). Use a small square to ensure that the splitter is also square to the tabletop.
Adjust the fence and miter gauge
For safe, clean cuts, the rip fence must be adjusted parallel to the blade. Because you have already adjusted the table slots to the blade, you can now adjust the fore and aft ends of the fence to the slots, as shown in Photo Q. Most importantly, make sure that the aft end of the fence doesn’t angle inward toward the blade, which invites pinching and kickback. Some woodworkers angle the aft end away by 1⁄32' or so for a measure of safety.
The fence faces should also be adjusted square to the table. Some fences include adjustment screws in the crossbar to correct tilt (Photo R). Without them, adjusting a tilted fence generally requires shimming between the faces and the fence body. (For metal-faced fences, you may need to attach a shop-made facing.)
For accurate crosscutting using a miter gauge, its bar must fit snugly in the table slots without sideways play. The miter gauge head must also be aligned perfectly square to the blade. The time-honored low-tech trick to correct the fit of a loose bar is to dimple its edges with a metal punch to expand the metal a bit. If aggressive pounding causes the bar to then stick in its slot, file the edges of the bar down a bit.
Once the bar fits well, use a drafting triangle to set the miter gauge head square to the blade (Photo S). Then adjust the 90° stop on the miter gauge head. Also use the triangle to set the 45° stops.
Cleaning and protecting surfaces
Clean the saw table and fence rails with mineral spirits. Scrub away light rust using fine steel wool lubricated with mineral spirits. For heavier rust, use the finest grit possible of silicon carbide wet/dry paper, again lubricated with mineral spirits.
Wipe away the spirits. Wax the table top, the rails, and areas where the fence contacts them. Also wax the faces of the fence, buffing the wax well with a soft, clean cloth. While various metal protectant sprays seem to work fine, I’ve not found them to be any better than paste wax.
About Our Author
Senior editor Paul Anthony is the author of Taunton’s Complete Illustrated Guide to Tablesaws, from which this article is excerpted.